UK · EU reference Tyre Pressure

255/70R16 · pickup / double-cab · PSI

What PSI for 255/70R16 tyres?

Size
255/70R16
Class
pickup / double-cab
Planning PSI
35
Planning bar
2.41

psi

35

2.41 bar · 241 kPa · pickup / double-cab planning figure

255/70R16 · 35 psi · 2.41 bar · 241 kPa — estimates. Placard wins.

PSI is the garage-hose number. For 255/70R16 a typical pickup / double-cab planning figure is 35 psi cold — about 2.41 bar or 241 kPa. 16-inch crossover-truck overlap. These rows are estimates interpolated for the size, not OEM for a named VIN.

Estimated 255/70R16 pressure by load

These 255/70R16 load steps are ± a few PSI from 35. They are not a licence to ignore a printed second column on a van or estate.

ConditionFront (est.)Rear (est.)
Driver only / unladen35 psi / 2.41 bar / 241 kPa37 psi / 2.55 bar / 255 kPa
Typical occupancy35 psi / 2.41 bar / 241 kPa38 psi / 2.62 bar / 262 kPa
Payload / towing (sketch)36 psi / 2.48 bar / 248 kPa39 psi / 2.69 bar / 269 kPa

PSI, bar and kPa

Use the table, then set a cold gauge. 241 kPa is 100 × 2.41 bar on this size.

PSIBarkPa
312.14214
322.21221
332.28228
342.34234
352.41241
362.48248
372.55255
382.62262
392.69269
402.76276
412.83283
422.90290
432.96296
443.03303
453.10310
463.17317
473.24324

What 255/70R16 means

A 255/70R16 on a pickup / double-cab is a geometry. Two cars can share the size and disagree on PSI because mass and axle split differ.

16-inch crossover-truck overlap. Rim diameter 16 in; section 255 mm. Estimates on this page assume a typical load index for the pickup / double-cab class.

Placard versus sidewall

This website maps size searches such as “255/70R16 psi”. It does not replace the VIN label. If the two disagree, the label wins.

Cars often seen on 255/70R16

These catalogue models are often seen on 255/70R16 or a close OEM neighbour. Open the vehicle chart for axle-specific PSI and bar.

How to set 255/70R16

  1. Measure before the school run, not after the motorway.
  2. Write LF / RF / RR / RL. Do not keep 255/70R16 numbers in your head.
  3. Add air in short bursts toward the placard, using 35 psi only as a map.
  4. If one 255/70R16 is 4 psi down, hunt for a nail before you blame the weather.
  5. Log date, ambient temperature and the four readings.

Temperature drift

Roughly 1 psi per 5–6 °C. The table uses 35 psi as a 20 °C baseline for 255/70R16.

AmbientGaugeBarkPaNote
−5 °C (hard frost)32 psi2.21 bar221 kPaGauge reads low; do not overfill once warm
0 °C33 psi2.28 bar228 kPaGauge reads low; do not overfill once warm
8 °C (UK winter morning)34 psi2.34 bar234 kPaGauge reads low; do not overfill once warm
20 °C (set cold here)35 psi2.41 bar241 kPaBaseline for this size sketch
30 °C37 psi2.55 bar255 kPaDo not bleed a hot 255/70R16
38 °C (heatwave tarmac)38 psi2.62 bar262 kPaDo not bleed a hot 255/70R16

Keep 255/70R16 on the printed band for that car; 35 psi is a size sketch, not a second VIN label.

Questions about 255/70R16

Should I bleed pressure after a motorway run?

No. Heat raises the gauge. Set cold only. Bleeding a hot tyre leaves it low the next morning.

Is the sidewall number correct for 255/70R16?

No. Sidewall PSI or kPa is a maximum for the carcass. Operating pressure is the door-pillar placard.

Is 255/70R16 the same as a plus-size swap?

Only if that is the size you fitted. Overall diameter should stay close to OEM. Pressure still follows the car, with load index at or above original.

What PSI should 255/70R16 tyres be?

A pickup / double-cab planning figure is about 35 psi cold (2.41 bar / 241 kPa). Confirm on the vehicle placard — two cars can share 255/70R16 and not share a sticker.

What is 255/70R16 in bar?

35 psi is 2.41 bar. Add a tenth of a bar if the placard’s laden column is higher, which is common on vans that wear this size.

Handbook: placard · bar vs PSI · cold inflation · all sizes