UK · EU reference Tyre Pressure

225/35R19 · passenger car · PSI

225/35R19 tyre pressure in PSI

Size
225/35R19
Class
passenger car
Planning PSI
36
Planning bar
2.48

psi

36

2.48 bar · 248 kPa · passenger car planning figure

225/35R19 · 36 psi · 2.48 bar · 248 kPa — estimates. Placard wins.

If someone typed “225/35R19 psi”, they want Imperial. Start near 36 psi on an unladen passenger car, then confirm the vehicle placard. Sidewall max is not the target. A 10 °C overnight drop takes roughly 1 psi (0.07 bar) off a closed 225/35R19. Low-profile {sz} does not want a “softer” pressure to recover ride. Stay at or slightly above the car’s original placard if load index is kept.

Estimated 225/35R19 pressure by load

Plus-sizing to 225/35R19 from a taller OEM tyre usually keeps the same placard if the load index is equal or higher.

ConditionFront (est.)Rear (est.)
Driver only / unladen36 psi / 2.48 bar / 248 kPa36 psi / 2.48 bar / 248 kPa
Typical occupancy37 psi / 2.55 bar / 255 kPa38 psi / 2.62 bar / 262 kPa
Motorway + luggage (sketch)38 psi / 2.62 bar / 262 kPa39 psi / 2.69 bar / 269 kPa

PSI, bar and kPa

1 bar ≈ 14.5 psi; 1 psi ≈ 6.89 kPa. Planning midpoint for 225/35R19: 36 psi = 2.48 bar = 248 kPa.

PSIBarkPa
322.21221
332.28228
342.34234
352.41241
362.48248
372.55255
382.62262
392.69269
402.76276
412.83283
422.90290
432.96296
443.03303
453.10310
463.17317
473.24324
483.31331

What 225/35R19 means

225/35R19 means a 225 millimetre section width, a sidewall that is 35 percent of that width, on a 19-inch rim. The R is radial construction.

Low 19-inch compact. Rim diameter 19 in; section 225 mm. Estimates on this page assume a typical load index for the passenger car class.

Placard versus sidewall

This website maps size searches such as “225/35R19 psi”. It does not replace the VIN label. If the two disagree, the label wins.

Cars often seen on 225/35R19

These catalogue models are often seen on 225/35R19 or a close OEM neighbour. Open the vehicle chart for axle-specific PSI and bar.

How to set 225/35R19

  1. Park so the 225/35R19 tyres are cold (three hours, or less than about a mile).
  2. Read the door-pillar placard for that car — not the 225/35R19 sidewall maximum.
  3. If the sticker is missing, 36 psi / 2.48 bar is only a passenger car planning figure for this size.
  4. Set all four with a calibrated gauge. A 3 psi miss on one corner shows up as a wander.
  5. Refit valve caps and reset TPMS if the handbook asks for a relearn.

Temperature drift

Roughly 1 psi per 5–6 °C. The table uses 36 psi as a 20 °C baseline for 225/35R19.

AmbientGaugeBarkPaNote
−5 °C (hard frost)33 psi2.28 bar228 kPaGauge reads low; do not overfill once warm
0 °C34 psi2.34 bar234 kPaGauge reads low; do not overfill once warm
8 °C (UK winter morning)35 psi2.41 bar241 kPaGauge reads low; do not overfill once warm
20 °C (set cold here)36 psi2.48 bar248 kPaBaseline for this size sketch
30 °C38 psi2.62 bar262 kPaDo not bleed a hot 225/35R19
38 °C (heatwave tarmac)39 psi2.69 bar269 kPaDo not bleed a hot 225/35R19

Keep 225/35R19 on the printed band for that car; 36 psi is a size sketch, not a second VIN label.

Questions about 225/35R19

What PSI should 225/35R19 tyres be?

A passenger car planning figure is about 36 psi cold (2.48 bar / 248 kPa). Confirm on the vehicle placard — two cars can share 225/35R19 and not share a sticker.

Is the sidewall number correct for 225/35R19?

No. Sidewall PSI or kPa is a maximum for the carcass. Operating pressure is the door-pillar placard.

Can I run 225/35R19 at a lower pressure for comfort?

Not as a habit. A soft 225/35R19 cooks the shoulders and dulls steering. Keep load index and stay on the placard.

What is 225/35R19 in kPa?

248 kPa is the planning midpoint (100 kPa = 1 bar). 255 kPa is one PSI higher.

Should I bleed pressure after a motorway run?

No. Heat raises the gauge. Set cold only. Bleeding a hot tyre leaves it low the next morning.

Handbook: placard · bar vs PSI · cold inflation · all sizes